Audi B8/C7/D4 Spherical Front UCA Bushings (SPC Adjustable Arms) (B8006A1)
Set of 4. Core exchange not available for this product.
Set of 4. Core exchange not available for this product.
Set of 4. Core exchange not available for this product.
The front upper control arm bushings are responsible for controlling the camber and caster of the front wheels. Rubber bushings allow the camber and caster to change substantially during cornering, resulting in toe changes, loss of grip, and increased wear on the shoulders of the tires. The spherical upgrade holds the alignment under load, keeping the alignment where it was set at all times.
We use only the highest quality motorsport-grade PTFE-lined bearings for best performance and lifespan. We use high strength 7075 aluminum for the bolt sleeves, and 6061 for the bearing cups. Bearings are interference-fit into the cups, so they wonโt rattle. Both internal and external retaining rings ensure everything will always stay in place.
Please note that lifespan will vary based on the application and driving conditions. Spherical bearings do have moving parts, so they do wear. Our bearing kits are fully rebuildable. Please contact us for rebuild kits.
Rubber bushings act like little springs at each suspension pivot point. They allow suspension geometry to change under load, ruining your alignment and causing unwanted handling characteristics like steering wander, binding, camber, caster, and toe changes, and lack of steering and suspension feedback. Spherical bearings do not bind or flex under load, creating perfect suspension joints.
Spherical bearings are known to produce creaks and pops in the suspension as they age. Though we only use PTFE-lined motorsport grade bearings (the best and most durable you can get), weโve found the PTFE liner is rarely sufficient to keep the bearing fully lubricated and free-moving over the course of its life. Weโve found after a year or two, some bearings will start to creak right as they start moving or when they switch from moving one direction to the next. As they start to wear they will also become looser over time, eventually making a very small gap between the ball and outer race. This gap can cause a noise similar to if you had a slightly loose bolt or ball joint. When these symptoms start to occur, relubricating them with a synthetic PTFE grease will quiet them down and smooth out their movements very nicely. We recommend doing this at least once per year or every 5 to 10 thousand miles as part of a regular maintenance routine. A thick layer of grease covering the exposed parts of the bearing will also act as a moisture and dust barrier, keeping as much crud out as possible. The more often you can clean and regrease, the more life youโll get out of them. Weโve found with proper care you can get 20-40,000 miles out of a set of bearings.
With all this said, please understand that these bushings are designed around ultimate performance in motorsport settings. With anything high performance will come more maintenance, and these are no exception. Please consider whether you are willing to sign up for the maintenance before going the spherical route.
A few tips to get these pressed in correctly.
Use a hydraulic press. A typical screw-driven bushing installation tool will not have the strength to do it.
Lubricate the mating surfaces well before installation. This will reduce press forces by around 50% and greatly reduce the risk of damage to the control arm or bushing.
Measure the diameters of the hole and the bushing before installing. OEM (and especially aftermarket) control arm hole diameters can vary pretty wildly. Interference of .002-.007โ is ideal. Looser and they may knock around. Tighter and they may require extreme press forces and will be very likely to gall the mating surfaces during installation. If the interference is too high, you can lightly sand/file/ream the hole out until itโs in the correct range.
For easier installation, heat the control arms and cool the bushings. This will reduce the interference thereby reducing the press forces needed.
Make sure the control arm hole is clear of burrs, debris, and any abnormalities.
Usually one side of the control arm hole is tapered. Press the bushing in from that side for easier, safer install.
Wear eye protection and be safe. Press forces often exceed 5 tons. If/when something breaks or your assembly contraption slips, it can be extremely dangerous.
We cannot be responsible for damage or injury due to installation mishaps, though we will work with you to subsidize replacement parts. Be careful. If in doubt about your abilities to do it correctly, use our core exchange program or contact us and send us your control arms and weโll do the installation for you.
Fits the following vehicles:
Audi B8 A4/S4/RS4/A5/S5/RS5
Audi B8 Q5/SQ5
Audi C7 A6/S6/RS6/A7/S7/RS7 (please send us a message before ordering)
Audi D4 A8/A8L/S8 (please send us a message before ordering)